Beoordelingen voor VEVOR Druktank Verftank Spray Paint Drukpot 2L Druktank 45psi Spuitpistool Verftank Φ38.5 x 12.6c Spray Paint Drukpot Tank Verfcontainer Verfspuitpistolen Verven, vlekken

klanten-reviews

4.7 Uit 5

Gebaseerd op 36 beoordelingen

Beoordelingen per functie

Prijs 4.7
Kwaliteit 4.5
Functies 4.6
Makkelijk te gebruiken 4.5
Bekijk Meer Minder zien

6 Beoordeling(en)

Tekst, beeld, video

Alleen foto's

Alleen video's

Alleen 4 sterren

Ster

Alleen 5 sterren

Alleen 4 sterren

Alleen 3 sterren

Alleen 2 sterren

Alleen 1 ster

Meest recente

Meest behulpzaam

Wis filters

Bert

Goede aankoop

Beoordeeld op Mar 19, 2025

Ik gebruik enkel de drukketel om om lijm op druk te kunnen brengen. Werkt goed. Drukregelaar een beetje fragiel.

Bekijk Meer Minder zien

Behulpzaam Feedback verzenden... Bedankt voor je feedback. 0 mensen vonden dit nuttig

Nick Manning

Decent but cautious of quality control on parts

Beoordeeld op Feb 15, 2025

Pressure vessel holds and is easy to set up and use. Though when testing for my first use, the ball valve was leaking the pressure when attempting to tighten the fitting it sheared with little torque. Replaced with parts from hardware stores.

Bekijk Meer Minder zien

Behulpzaam Feedback verzenden... Bedankt voor je feedback. 0 mensen vonden dit nuttig

Diggah

A great pressure pot for resin casting.

Beoordeeld op Mar 23, 2023

I got this to convert into a pressure pot for resin casting as it’s the same as the widely referenced Habour Freight pressure pot that a lot of American YouTubers recommend. Getting the parts off was a bit of a hassle as they’re sealed with glue, so I has to resort to a blowtorch to melt the glue in order to remove the fittings. The T pieces are junk and leak even with ALL the PTFE but the rest is sound. Pressures nicely to 55psi without issue. Recommended.

Bekijk Meer Minder zien

Behulpzaam Feedback verzenden... Bedankt voor je feedback. 0 mensen vonden dit nuttig

Steve

Beoordeeld op Jul 22, 2022

Good bit of kit, sturdy & seems to be well made. I've converted it into a pressure pot for resin casting, holds the pressure after capping off the outlet & fitting a tap to the inlet.

Bekijk Meer Minder zien

Behulpzaam Feedback verzenden... Bedankt voor je feedback. 0 mensen vonden dit nuttig

d armstrong

customised for resin , work fine but not happy with some of the fittings

Beoordeeld op Nov 21, 2020

so I need to start this review by stating I'm not using the pressure pot for what it was designed for , I have converted it for resin casting . It would have been 5 stars apart from some of the fittings , mainly the regulator and gauge .The pot is relatively cheap with most of them _50 to _100+ more so I have taken that into account , pot is a well made thick gauge metal with a silicon seal in the lid , the air inlet has a side diverter meaning its not going to blow the resin etc out of the mould when you charge it . everything fitted to it is fine until you get to the pressure gauge and associated fittings , the body is plastic and already out of shape from shipping , feels like its going to fall apart just from handling however the biggest issue is its rated in MPA not PSI or BAR , which is easy to convert with google but an added complication and it goes way over what the vessel is rated for which could lead to some very nasty accidents if you don't get it right .The pressure vessel is easy to convert with a couple of extra fittings and PTFE plumbers tape but I would strongly recommend replacing the regulator with a decent PSI rated one before use .I did put 40 psi into the unit 24 hours ago and it has held the pressure . The inside is a decent size for most of the turning and casting work I would ever need to put in it .in summary - buy a decent gauge and its a very handy tool

Bekijk Meer Minder zien

Behulpzaam Feedback verzenden... Bedankt voor je feedback. 1 mensen vonden dit nuttig

Dakota

Turned it into a pressure pot for resin casting.

Beoordeeld op Feb 20, 2021

The gauge leaks, therefore cannot hold pressure until replaced.As long as you do a small amount of research or know what you're doing this can very very easily be turned into a pressure pot for resin casting. I use it as 50-55 psi and just had to plug one side and buy a new gauge ($8) not a big deal but just a heads up. That being said, I also used thread seal just to be sure there is no leaks. Teaming it with a small compressor, I had a functioning pressure pot w/compressor for ~$220 which is great in my opinion.In short, worth the small amount of work it took to convert it. And it is holding pressure and functioning great.

Bekijk Meer Minder zien

Behulpzaam Feedback verzenden... Bedankt voor je feedback. 1 mensen vonden dit nuttig

Klantbeoordelingen voor VEVOR Druktank Verftank Spray Paint Drukpot 2L Druktank 45psi Spuitpistool Verftank Φ38.5 x 12.6c Spray Paint Drukpot Tank Verfcontainer Verfspuitpistolen Verven, vlekken

klanten-reviews

Beoordelingen per functie

Mensen die dit artikel kochten, kochten ook