Klantbeoordelingen voor VEVOR Verfspuit Spuitpistool 2-1/2 Gallon Pressure Feed Paint Tank Pot Sprayer Us Stock Industrial Sprayer System

I'm really happy with this pot. There are loads of videos on YouTube showing how to convert it for resin casting. I pressurise mine to 60 psi and it holds perfectly. Bear on mind you'll always lose a couple of psi as the air cools back down. To convert this in the same way I have, you'll need... 3/8x1/4 bsp male x male fitting 1/4 bsp Tee (all female) 1/4 female to male ball valve 1/4 male to whatever your compressor or pump uses 1/4 pressure gauge (the pot comes with one but I chose to get a sturdier one) Ptfe tape The pot also comes with a pressure release valve There are two holes in the lid, one is 1/4 and one us 3/8. I screwed the pressure release valve straight into the 1/4. I assembled the other as in the photo but switched the gauge and inlet around. use 3 wraps of ptfe on each thread. This is how I put it all together, do lots of research and make sure you're confident :) If this was useful or if you have any questions, pop to instagram and say hi! https://www.instagram.com/discover_rings/?hl=en-gb

Not used it yet as I have not been doing anything to paint but we'll let you know later if it isn't good product

Excellent piece of kit. Sealed lid for first time, filled it with air to 50psi. Disconnected compressor and left for 3 days. The psi was still 50, never had that before with a pressure pot. Used it several times since and still holding pressure, no leakage at all. Good quality. I cut off the liquid out pipe inside as it interfered with caddy. Excellent thanks.

Excellent sprayer, reducing painting time by 80 per cent .very easy to clean and set up for the products I am putting through it , thank you very much for a very very good product

I ordered the smaller 10l pressure pot from Vevor. It seems designed for resin casting but still has a paint pipe installed in case you want to spray paint. This gets in the way of casting. I think Vevor should remove it. I did - with an angle grinder. I couldn't unscrew it. The pot works fine up to 50 psi (which is high as I need to go). No bubbles in the resin. No leaks from any point on the pot either, so no need for the supplied sealant. For £114, this pressure pot is way cheaper than the competition. I didn't find any CE quality marks and I haven't tested the safety pressure release (60psi) but it works well. If Vevor supplied castors the price would be a little higher, but I think they could remove the paint pipe (as an option?) or blank off that fitting without a major cost and sell it for the purpose most purchasers will use it for - resin casting. It would be good if they supplied an adjustable caddy as well as the internal base plate. Overall however, I'm very satisfied.

good quality great value, well built and hoping for many years use, have been always haappy with items bought from vevor

I got this to convert into a pressure pot for resin casting as it’s the same as the widely referenced Habour Freight pressure pot that a lot of American YouTubers recommend. Getting the parts off was a bit of a hassle as they’re sealed with glue, so I has to resort to a blowtorch to melt the glue in order to remove the fittings. The T pieces are junk and leak even with ALL the PTFE but the rest is sound. Pressures nicely to 55psi without issue. Recommended.

Does what it’s supposed to and made work easier

I bought this to make a pressure pot for resin casting. Build quality is excellent for the price and by spending a couple of quid on fittings it’s up and running and holding pressure for 24 hours.

Brilliant bit of kit. I converted it into a resin casting pressure pot, the paint extraction pipe and paint agitator all unscrew so all that’s needed is a bolt with 2 metal washers and 2 rubber washers for where the agaitator pipe goes.It’s sits it about 45psi comfortably without the air compressor attached, so the resin can cure overnight.Extremely happy with the product