Klantbeoordelingen voor VEVOR Ultrasoon Reiniger 0.8L Ultrasonic Cleaner Digital Timer Jewelry 40KHz Tub Basket Factory Direct

I bought this to clean bike parts. I have only used it once so far and it worked great. I put my drive chain in the cleaner and 40 minutes later it was clean. The only issue I had was that I needed to change outlets as the initial surge when I turned it on tripped the ground fault breaker on the first outlet I used. It does take a while for the cleaning solvent to get to temperature. It was still going up at the end of the cleaning cycle. I used water and a little Simple Green as the solvent.

Worked great to clean some model engine mufflers that had become heavily stained. Using plain distilled water had little cleaning power but when a proper solution of 'Sensitive metals ultrasonic solution' supplied by allendale-ultrasonics.co.uk. was used it worked great. One part to 10 parts distilled water.

Bought this in the UK - TBH when I got the PayPal receipt I panicked and began searching the web for reviews and to check if Vevor were legitimate or another Shopify scam. Well, they are not - I couldn't be happier with my purchase. Great price, item delivered as expected and far sooner than expected - it was within 4 days! Well done Vevor!

Not a 100% vitally necessary item but one which has made some jobs much easier, cleaner and far more efficient. There is a knack to making best use of it though. Use preheated water and put smaller items in smaller container your cleaning solution and that way you can use plain water in the main tank and not contaminate the tank with grease, oil etc. Using small containers does NOT affect the cleaning action. Cracking piece of kit if used correctly and at price that doesn't break the bank. Just make sure you buy big enough for all your uses otherwise buyer regret slips in. I judged mine just about spot on; big enough to clean my CPAP water container.

This isn't a high-end professional ultrasonic cleaner, but it's way more affordable and "good enough" for most uses outside of a lab. I bought it to clean flux residue off circuit boards and my first attempt went extremely well.I used about 350mL of Chemtronics Flux-Off with 1 gallon of distilled water. The specs for Flux-Off recommends running at 60degC, but the water only got up to 45degC at the end of a 30 minute cycle. I likely could have let it run for an hour first to let it warm up fully and de-gas the solution, but I was anxious to try it out. Despite running below spec, the PCB came out clean.The cleaner came with a drain hose and adapter, but I need a smaller hose to fit through the opening in a 5 gallon jug that I got from ULINE. I ended up getting a brass 3/8" thread to 3/8" barb adapter and a 1/2" hose. At the end of the cycle, I just opened the valve and everything drained into the waste jug. Very convenient!I really should have used deionized water instead of just distilled. The distilled water left a few water spots, which DI is less likely to do. I'm planning to get a 4-stage RO/DI filtration system to make my own DI water instead of buying it online.Overall, I'm very happy with this. As long as you don't expect a industrial-grade piece of equipment, I think you'll be happy too.

This thing is a monster.. We had an old meat grinder we needed to get cleaned up. The heat function on this outdoes the fact that my smaller cleaner doesn't heat. It really helps break gunk down and pull it off the parts. Old meat grinder came out gunk free and functioned extremely well on first try. It wouldn't even turn before we put it through a cycle in this tank.It is big enough to fit lots of stuff in. Highly recommend

Well made, powerful ultrasonic cleaner with a decent sized bath for larger more square shaped jobs, such as long case clock movements.

A must for those that love to clean, this unit is great, heating up takes a while but once its up to temperature holds it well. Hogh quality for the cost its amazing.

Is a nice unit but only holds 4l not 6l

First impression, looks very professional but noticed a couple of tiny dents after a close inspection.Not that noticeable unless your looking for them.I filled it with water to test the machine, firstly I just used the heater and checked with my smart meter monitor that it was 600w.... However I then added the cleaner which should have been 1200w total.It was barely averaging 1000w with fridge and freezer on...I've just ordered a plug-in energy monitor to check the precise wattages of heater or/and cleaner.My machine has 10 x 60w transducers so if results are 480w for cleaner then 2 transducers are faulty.Then I shall send it back......... will let you know